Power Enengy Sector
2 Way Radios & Accessories
IC-F3161DT/DS, IC-F4161DT/DS (FM Approved version)
IDAS™ digital mode ready
The IDAS (Icom Digital Advanced System) is Icom’s digital conventional and trunking system based on the NXDN™ common air interface.
It has useful calling features including selective calling, status message, radio stun/kill/revive, etc.
IP55 dust-protection and water jet resistance
The IC-F3161D series meets IP55 requirements for dust-protection and water jet resistance. Its durable construction is backed up by the aluminum die-cast chassis and polycarbonate casing, allowing reliable operation under harsh weather and environmental conditions.
Lithium-Ion battery pack
The supplied 2000mAh (typ.) Li-Ion battery pack, BP-232FM, provides 14 hours* of operating time.
* Typical operation Tx:Rx:Stand-by=5:5:90, power save on
Most popular signalings built-in
The 2-Tone, 5-Tone, CTCSS, DTCS and MDC signaling capabilities are built-in for group communication or selective calling. The radio can decode ten 2-Tone codes or eight 5-Tone codes on a channel. When a matched tone is received, the following actions are programmable for each code.
• Beep sound
• Bell icon
• Answer back call
• Auto TX
• Radio stun/kill/revive
Basic LTR™/conventional mode operation
Both LTR™ trunking and conventional channels are programmable on a radio. Group, selective (DTMF), and phone call are available in LTR™ mode.
MDC 1200 Compatible
The following selective calling and ANI features are available with the built-in MDC signaling.
• PTT ID
• Radio check
• Radio stun/revive
• 500 Aliases
• Status message/request
• Call alert
• Emergency, emergency mic monitoring
Voting mode scanning
The voting mode scanning detects the signal strength level of repeater stations and automatically selects the strongest station, useful for roaming between 2 or more repeater sites. Once you program the voting mode to a memory zone, you can easily start voting mode operation by changing the zone setting.
Full dot-matrix LCD
Using a large full dot-matrix LCD (32 × 18 mm), the IC-F3161D series shows upper and lower case characters clearly. The display setting is selectable from 1 line, 12 characters or 2 lines 24 characters via programming. The bottom row shows assigned functions to the [P0] to [P3] buttons.
The IC-F3161D series employs a BTL amplifier that increases the audio output and the built-in audio compander provides clear, low noise communications.
Lone worker function
When the radio is not operated for a preset period, a beep sounds and a button push is required. If no button is pushed within that preset time, an emergency signal automatically transmits and alerts your co-worker or dispatcher to any potential trouble.
The Intrinsically safe version is approved by the FM Approvals. It is suitable for use in hazardous areas where flammable gasses or liquids are used.
IS: Class I, II, III/ Div 1/ Groupes DEFG/ T3C Ta = 40°C
NI: Class I/ Div 2/ Groupes ABCD/ T3C Ta = 40°C
Special condition for use Must be used with the BP-232FM battery. The HM-169IS, VS-1SC, HS-94, HS-95 and HS-97 are approved as intrinsically safe options. Any other options, except the antenna, belt clip and belt hanger, cannot be used in explosive atmosphere areas.
Never charge the BP-232FM (with/without the transceiver) in an explosive atmosphere. The optional battery chargers are not approved as intrinsically safe.
• 512 memory channel with 128 zones
• 8 DTMF autodial memories
• Built-in inversion type voice scrambler
• 2 step reduced power setting
• Busy, repeater lockout functions
• Escalating alarm
• Mode dependent scan
• Surveillance function temporarily turns off the LED backlight and beep sound
• Powerful 5W output both in VHF and UHF
• Flash CPU for future upgrade and more…